Skip to section:
Users of hot melt should perform their own tests to satisfy themselves that the adhesive selected, with adequate controls in place to ensure correct usage, will suit their requirements.
Generally, testing of a bond should not be made until at least 24 hours after the application.
Hot melt glues are thermoplastic polymer based materials in solid form which contain no solvents, VOC’s or water and are non-hazardous, FDA approved and leave no risk of mould or odours in finished product. In use, they are heated and applied molten to one surface of the parts to be glued, when the surfaces are pressed together the hot melt quickly cools to form an almost instant bond.
Hot melt Adhesives can be formulated using several different base polymers. The choice of polymer affects adhesion, temperature resistance, chemical resistance and cost.
Over recent years, developments have allowed many product assembly applications to benefit from the efficiencies of hot melt adhesives. High performance bonding is now possible on a variety of substrates; however final bond strength will vary depending upon the following criteria:
The open time is the period available to make a satisfactory bond after the hot melt adhesive has been applied. This can be as short as a second or two or be up to several minutes.
The maximum open time of a hot melt adhesive is dependent upon these factors:
For maximum bond strength, it is important to get the parts together as soon as the adhesive has been applied. The different factors that affect open time mean it is not practical to quote exact times, therefore the open times of TECBOND® hot melt adhesives are broadly classified into three groups: Short (1-15 seconds), Medium (15-30 seconds) and Long (30-60 seconds).
Values shown have been measured using standard ASTM D3236.
When solid hot melt is heated it melts, the higher the temperature the more liquid the glue becomes. This liquid state is known as the viscosity, expressed in centipoises and measured with a viscometer. TECBOND® hot melts can be dispensed at varying temperatures therefore their viscosity is expressed broadly as: Low (500-3000cps), Medium (3000-6000cps) and High (6000-15000cps).
Low viscosity glue flows freely and can increase gun output, reduce stringing and give closer bonds. It is less suitable for porous materials such as foam or fabric.
High viscosity glue may reduce gun output but is suitable for uneven surfaces or where gap-filling or low-sag qualities are needed. Choosing a more powerful tool would improve output when using high viscosity glues.
Values shown have been measured using standard BS5350 Part H3.
Hot melt adhesives are thermoplastic and, as such, their performance alters with temperature. One of the more noticeable changes is the loss of bond strength alongside increasing temperature. Heat resistance is a measure of bond strength for hot melt adhesives, relating to the temperature (in °C) at which a standardised sample, when subjected to a constant load, fails.
Ring and Ball Softening Point (the point at which the adhesive becomes liquid – usually a higher value than the heat resistance figure for any given adhesive) is often quoted for hot melt and should not be misinterpreted as a measure of heat resistance.
Because bond strength can be influenced by several other factors (i.e. type of adhesive, length of time exposed to elevated temperature, magnitude and direction of the load imposed on the bond line, and the nature of the substrates being bonded), the quoted heat resistance figures of TECBOND® hot melts should only be used as a general guide when comparing different adhesives. It should not be assumed that the adhesives will be able to withstand the quoted temperatures in all cases.
The user should determine the suitability of an adhesive for their particular application.
To ensure the best performance from your gun follow these tips:
HEALTH & SAFETY ADVICE
Hot Melt adhesives pose virtually no hazards to health when used in normal industrial practice but because they are used in a molten state at high temperatures, there is a risk of thermal burns.
Skin contact with molten hot melt should be avoided and precautions should be taken against accidental splashes of adhesive. The use of overalls, cotton gloves and safety glasses can help minimise the risk of burns.
Skin affected by molten hot melt should be plunged into cold water immediately and left until the burning sensation subsides. If no tap is accessible have a bucket of clean cold water available. If fingers are coated with hot melt, move them to prevent a tourniquet effect as it cools.
Do not remove the adhesive when molten as it could remove skin leaving a raw wound. Even when solid remove with care as this may still occur. If difficult to remove, with medical approval, olive oil or liquid paraffin should be soaked into a cotton wool pad and placed over the affected area. This will slowly soften the adhesive into the pad. When hot melt is removed treat as a normal burn.
Solid cold hot melt is harmless to the skin. Wash hands with soap and water.
Treat solid hot melt as inert particles and irrigate copiously with clean fresh water. For molten hot melt irrigate with cold water and seek medical advice immediately.
Vapours given off during normal operation are not considered toxic, but if overheated, chemical breakdown of the components may occur releasing a complex mixture of organic materials, some of which may be toxic or irritant. Ensure hot melts are run at the recommended operating temperatures and use in a well-ventilated area.
Removal of hot melt from components
Assembled components can be separated by heating the assembly gradually until the glue softens enough to be removed. Residues of EVA and Polypropylene based hot melt can be removed with white spirit. Residues of Polyamide based hot melt can be removed with acetone. Prior to cross linking, PUR adhesive can be removed with white spirit or acetone but once cross linking is complete, removal is very difficult.
Hot Melts are only combustible in a fire and to extinguish use dry powder or CO2 extinguisher. Do not use water.
Store in a clean dry place at a temperature between 5°C-30°C with boxes closed. Do not expose to direct sunlight or localised heat sources such as radiators or hot pipes.
TYPICAL SPRAY COVERAGE
Using 420-43 adhesive dispensed with a 6300 tool at 90 psi
RED nozzle (PA6056) spraying 55mm width gives about 120 metres per kilo
YELLOW nozzle (PA6060) spraying 65mm width gives about 140 metres per kilo
BLUE nozzle (PA6064) spraying 75mm width gives about 120 metres per kilo